![]() ![]() To configure your MGate MB3660, connect the gateway’s Ethernet port directly to your computer’s Ethernet port and then log in from a web browser. Pull High/low Resistors for the RS-485 portĭefault SW 1 2 3 Pull High Pull Low Terminator ON 1 K0 1 KS) 1200 OFF 150 K0 150 K0 – Software Installation Information To set the pull high/low resistors to 1 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to ON. To set the pull high/low resistors to 150 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to OFF. To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON set switch 3 to OFF (the default setting) to disable the termination resistor. The sequence from right to left is port 1 to port 16. To expose the DIP switches located on the back of the PCB, first, remove the screws holding the DIP switch cover in place, and then remove the cover. The MGate MB3660 uses DIP switches to set the pull high/low resistor values for each serial port. When using termination resistors, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. In some critical environments, you may need to add termination resistors to prevent the reflection of serial signals. Termination Resistor and Adjustable Pull High/Low Resistors The heads of the screws should be 5.0 to 7.0 mm in diameter, the shafts should be 3 to 4 mm in diameter, and the length of the screws should be more than 10.5 mm. With the plates attached, use screws to mount the unit on a wall. Attach the plates to the unit’s rear panel with screws. Two metal plates are provided for mounting the unit on a wall or inside a cabinet. STEP 4: Connect the power supply to the unit. The unit may be placed on a horizontal surface such as a desktop or mounted on the wall. STEP 2: Connect your device to the desired port on the unit. STEP 1: After unpacking the unit, use an Ethernet cable to connect the unit to the network. ![]() LAN 2 Green Indicates 100 Mbps Ethernet connection Amber Indicates 10 Mbps Ethernet connection Off Ethernet cable is disconnected Hardware Installation Procedure Respond properly, or a relay output occurred Green Steady on: Power is on and the unit is functioning normally Blinking: The unit is responding to the locate function Off Power is off, or power error condition exists Tx Green The serial port is transmitting data Rx Amber The serial port is receiving data LAN 1, PWR 2 Red Power is being supplied to the power input Off The power cable is not connected Ready Red Steady on: Power is on and the unit is booting up Blinking: IP conflict, DHCP, or BOOTP server did not LED Indicators Name Color Function PWR 1, Release the reset button when the Ready LED stops blinking. Hold the reset button down for five seconds using a pointed object such as a straightened paper clip. The reset button is used to load factory defaults. Reset Button- Press the Reset button continuously for 5 sec to load factory defaults AC-DB9 Models DC-DB9 Models AC-DB9-I Models AC-RJ45 Models The MGate MB3660I series gateways provide 2 kV serial port isolation protection. Hardware IntroductionĪs shown in the following figures, the MGate MB3660-8 has 8 DB9/RJ45 ports for transmitting serial data, and the MGate MB3660-16 has 16 DB9/RJ45 ports for transmitting serial data. Notify your sales representative if any of the above items are missing or damaged. CBL-PJTB-10: Non-locking barrel plug to the bare-wire cable.PWC-C13US-3B-183: Power cord with the United States (US) plug, 183 cm.PWC-C13UK-3B-183: Power cord with United Kingdom (UK) plug, 183 cm.PWC-C13EU-3B-183: Power cord with Continental Europe (EU) plug, 183 cm.PWC-C13CN-3B-183: Power cord with three-prong China (CN) plug, 183 cm.PWC-C13AU-3B-183: Power cord with Australian (AU) plug, 183 cm.WK-45-01: Wall-mounting kit, 2 L-shaped plates, 6 screws, 45 x 57 x 2.5 mm.CBL-RJ45SF9-150: RJ45 to DB9 female serial shielded cable, 150 cm.CBL-F9M9-20: RJ45 to DB9 female serial cable, 150 cm.CBL-RJ45F9-150: RJ45 to DB9 female serial cable, 150 cm.CBL-RJ45M9-150: RJ45 to DB9 male serial cable, 150 cm.Mini DB9F-to-TB: DB9 female to terminal block connector.1 RJ45-to-DB9 female serial cable for console setting. ![]()
0 Comments
Leave a Reply. |